General Information
The propshaft is part of the drive train and is standardly used in vehicle construction whenever direct power transmission between the gearbox and axle drive is not possible. On the T4 Syncro, the propshaft runs centrally along the underbody to the rear, connecting the final drive to the rear differential and transmitting torque to the rear axle. The propshaft consists of at least two shaft sections connected by a universal or CV joint, enabling it to compensate for design-related offsets and operational angular changes.
Versions
Fundamentally, three different shafts were installed in the T4 Syncro:
2-piece propshaft (short wheelbase)
3-piece propshaft (short wheelbase)
3-piece propshaft (long wheelbase)
In the early model years, 3-piece propshafts were installed exclusively. With the 1996 facelift (GP), the 2-piece shaft was introduced, presumably for cost reasons. In parallel, however, there were also post-96 Syncros fitted with the 3-piece shaft. Whether a vehicle has a 2- or 3-piece shaft installed cannot be determined on the SWB (KR) by model year, engine variant or any other technical feature. Shaft installation followed no rigid rules. Only the LWB (LR) always had a 3-piece propshaft fitted. On the SWB (KR), only a visual inspection of the vehicle underbody will tell for sure.


The front section is available in two different versions: as a solid shaft and as a hollow shaft. Here too, there are no concrete allocations as to when which variant was fitted. The centre and rear sections are always hollow shafts.

Design & Construction
The following shows the construction of a 3-piece propshaft (LWB). The basic design is identical for all propshafts on the T4 Syncro. On the 2-piece propshaft, however, the centre and rear sections are manufactured as a single unit, resulting in reduced manufacturing effort and saving one CV joint as well as one centre bearing.

1) Front shaft section, 2) Centre shaft section, 3) Rear shaft section, 4) Front centring bush, 5) Rear centring bush, 6) Front flex disc (Hardy disc), 7) Splash guard on vibration damper, 8) Rear flex disc (Hardy disc) with vibration damper, 9) Front flange, 10) Rear centre bearing, 11) Front centre bearing, 12) Splash guard on centre bearing, 13) Rear flange, 14) Front CV joint, 15) Rear CV joint





The LWB propshaft differs solely by having an extended centre shaft section; otherwise it is identical in construction to the SWB shaft.
Technical Features
Flex Disc (Hardy Disc)
The front flex disc (Hardy disc) connects the output flange of the final drive to the front propshaft section. The flexible rubber disc is capable of compensating for angular misalignments—caused, for example, by engine pitching during load changes—as well as cushioning shocks in torque transmission. The flex disc features a steel sheet to protect against thermal radiation from the final drive, which causes accelerated ageing of the elastomer. There is an early version (701521127) and a revised version (7D0521127) of the flex disc, both of which are now listed under the same part number. The updated version features internal threads for securing the propshaft, requiring shorter bolts (M10x30) that no longer need to be locked with nuts as on the older version. Aside from this detail, the flex discs are identical in construction and fully interchangeable.



Torque is transmitted via positive locking of the bushes on both the output flange and the propshaft section.




CV Joint
As is standard practice in passenger cars, the Syncro propshaft is fitted with CV joints rather than universal (Cardan) joints. These compensate for both articulation angles and changes in length between the shaft sections. Dynamic angular and axial changes occur during operation due to the flexibly mounted engine/gearbox assembly and the rear differential. A CV joint allows smoother, more uniform power transmission than a universal joint and is generally maintenance-free. After 20–30 years, replacing the propshaft joints certainly makes good sense. Typical signs of wear include pitted ball tracks leading to clicking noises under load, or worn splines causing noticeable play in the joint. The CV joints of the T4 Syncro propshaft have a centring diameter of approx. 100 mm and are secured to the flange using M8x48 multi-spline (XZN) bolts. The back of the CV joints is sealed with a sheet metal cover.
-
Flanged Shaft Snap Ring2,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
-
CV Joint Grease MoS23,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
-
CV joint 100 mm99,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
CV Boot
The propshaft boots are designed to withstand high rotational speeds, meaning they dispense with bulky bellows that could expand due to centrifugal forces at high RPM and tear in the worst case. This is essential because the gear ratio in the final drive and rear differential causes the propshaft to rotate at 21:13 = 1.615 times (early models only) or 27:17 = 1.588 times wheel speed.
-
CV boot for propshaft CV joint39,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
Centre Bearing
The centre bearings support the shaft out of necessity close to the CV joints. They consist of a sheet metal cage, a rubber damper that isolates the propshaft from the bodyshell and absorbs shaft movements, and the rolling bearing itself. The rolling bearing was a custom fabrication by FAG under the designation FAG 577121B and was elaborately sealed with two interlocking EPDM profiles per side. Unfortunately, this bearing is no longer commercially available today. The dimensions are 30x55x19 mm.


Typical defects on the centre bearing include worn rolling bearings and, increasingly, heavily corroded bearing housings, as these were originally delivered with virtually no anti-corrosion coating. Furthermore, the rubber dampers lose their vibration-damping qualities over time as the material hardens, which becomes noticeable through increased cabin noise.


The centre bearings were discontinued long ago, and no suitable replacement is available from aftermarket suppliers either. Centre bearings from the VW LT are frequently recommended as replacements, but these cannot be fitted without modification. Either the rubber damper contacts the propshaft flange once installed, or the bearing cages must be machined and the bearing width shimmed. Directly fitting plug-and-play centre bearings in outstanding quality are available in our shop.
-
Propshaft centre bearing124,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
Centring Bushes
The pilot bearings (centring bushes) centre the propshaft on the spigot of the final drive or the input shaft of the rear differential, thereby ensuring the smoothest possible running of the entire shaft. The centring diameter is 16.0 mm at both the final drive and the differential. However, this centring is not rigid, as articulation angles can occur at both ends due to engine and gearbox movement, and the propshaft sections never align perfectly with the spigots. The centring ring is therefore floatingly mounted or vulcanised into the bush. To prevent corrosion on the spigot, the bush is finished with a shaft seal.
The bushes can easily be damaged during removal if the shaft is not pulled off the centring spigot as straight as possible, but is bent or tilted instead. This must be observed both at the front final drive and at the rear differential. When replacing the bushes, it is important to note that they have no end stop inside the propshaft. The bushes must be pressed in until a specific protrusion can be measured. We have measured this protrusion across a large number of propshafts and can recommend the following values:
Front section (centring at the final drive): 15.0 mm
Rear section (centring at the rear differential): 24.0 mm


-
Propshaft centring bush39,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
Vibration Damper
The rear flex disc (Hardy disc) with vibration damper connects the propshaft to the viscous coupling or rear differential, ensuring smooth, low-vibration running by eliminating torsional vibrations around the resonance frequency of the entire propshaft via its sprung, rotationally symmetrical mass. Due to its cup-shaped design, the damper can accumulate dirt that would cause propshaft imbalance; the mass is therefore sealed with a rubber cover on the front face.





Torque transmission is also achieved here via positive locking. Note that the original T4 Syncro damper with part number 701521309 features 22.0 mm bushes on both sides. The OEM damper is no longer available as a spare part. Rear flex discs from the Golf 4, Golf 5 or Tiguan 4Motion are often recommended for repairs, as their bolt circle matches. However, these dampers differ in the bush dimensions: the propshaft side has a 21.0 mm diameter, while the differential side is 22.0 mm. This design was presumably chosen because the damper’s lower profile allows it to be fitted reversed; differing centring diameters prevent this potential incorrect installation.

However, bushes that are too small prevent proper positive torque transmission in the T4 propshaft. Consequently, the bolt connection is subjected to shear loads and is not designed for friction-locked transmission of the full torque. As a result, load reversals can cause the damper to twist relative to the propshaft, which can lead to the mounting bolts working loose. It is essential to use a suitable flex disc with 22 mm bushes on both sides here.





A suitable vibration damper with 22 mm bushes on both sides, as well as bolts of the correct grade and length, is available in our shop.
-
Propshaft vibration damper234,90 €incl. VAT
plus shipping costs
Delivery time: 2–4 working days
Additional Information
Smooth Running
Owing to the relatively high operating speeds, propshafts are dynamically fine-balanced as a complete assembly to achieve exceptionally smooth running. This is accomplished by welding balance weights onto the outer circumference of the tubular sections.
During dismantling, care should therefore be taken to precisely mark the relative position of the individual sections to one another to ensure reassembly in the exact same orientation. Especially when removing the flanges (e.g. when replacing the centre bearings), the correct position of the flange on the shaft splines must be restored. Every propshaft section possesses a slight residual imbalance. If the propshaft is assembled unfavourably and these residual imbalances align at the same angle, the resulting imbalance can cause speed-dependent vibrations or booming noises in the floorpan area.
As vehicles age, propshafts suffer increasingly from corrosion. Balance weights are often only partially intact or already missing, which can adversely affect the smooth running of the propshaft. A poorly balanced propshaft causes accelerated wear on all components connected to the shaft.


Relevant Tightening Torques
Flex disc to final drive (M10): 55 Nm
Propshaft to flex disc (M10): 55 Nm
CV joint to flange (M8): 40 Nm
Centre bearing to bracket (M8): 30 Nm
Flange central bolt (M10): 60 Nm + high-strength threadlocker
Propshaft to vibration damper (M10): 55 Nm
Vibration damper to viscous coupling (M10): 55 Nm
Dimensions and Weights
The following compiles approximate dimensions and weights relevant for shipping purposes. Weights vary slightly depending on whether the front shaft section is solid or hollow. Bolt weights are not included. Length dimensions are approximate, as the CV joints can naturally shorten or lengthen the shaft slightly through axial plunge.
Lengths
Front section, all: 96 cm
Centre section, 3-piece shaft, SWB: 101 cm
Centre section, 3-piece shaft, LWB: 141 cm
Rear section, 2-piece shaft: 162 cm
Rear section, 3-piece shaft: 64 cm
Weights
Flex disc: 0.7 kg
Vibration damper OEM: 4.4 kg
Vibration damper allradbus: 2.7 kg
Front section, solid, without flex disc: 8.1 kg
Front section, hollow shaft, without flex disc: 7.4 kg
Centre section SWB: 6.7 kg
Centre section LWB: 8.7 kg
Rear section, 2-piece shaft, without damper: 8.6 kg
Rear section, 3-piece shaft, without damper: 8.9 kg
Depending on the version and completeness of the propshaft, shipping weight can vary considerably, as can easily be seen by adding the component weights below:
Propshaft, 2-piece, hollow, without flex disc, without damper: 16 kg
Propshaft, 3-piece, solid, LWB, with flex disc, with damper: 30.8 kg


